玻璃钢滑梯是儿童水上游乐园内的一种非常受欢迎的设施，当然它的使用也是很频繁的，因此安全就是大家很关心的事情，下面儿童水上游乐设施厂家为您讲解下玻璃钢滑梯的保养和维修。

The glass fiber reinforced plastic slide is a very popular facility in the Children's Water Park. Of course, it is also used frequently. Therefore, safety is a matter of great concern. Now, the manufacturer of children's water recreation facilities will explain the maintenance and repair of the glass fiber reinforced plastic slide.

玻璃钢滑梯的保养：

Maintenance of FRP slide:

1、每日开放前，应对滑梯进行检查，察看滑梯有无外露的锐边、尖角、毛刺、漏水等现象。

1. Before opening every day, the slide shall be checked to see whether there are exposed sharp edges, sharp corners, burrs, water leaks, etc.

2、水处理设备是否正常运转，以保障滑梯润滑水及滑梯落水池的水的供给。

2. Whether the water treatment equipment operates normally to ensure the supply of lubricating water for the slide and water for the slide sump.

3、对连接件要定期检查并紧固。

3. Regularly check and fasten the connectors.

4、对承重构件应定期检查，看结构有无裂纹产生以及弯曲变形等。以便及时更换。

4. The load-bearing components shall be inspected regularly to see if there are cracks and bending deformation in the structure. For timely replacement.

5、滑梯在非使用期间应用塑料布或粗布遮盖以防止紫外线照射造成滑梯老化、褪色、产生裂纹等。对有裂纹的滑梯槽段应及时更换（或修补），滑梯接口不平整、倒凸台或有裂口时应及时处理。

5. The slide shall be covered with plastic cloth or coarse cloth during non use to prevent the slide from aging, fading and cracking caused by ultraviolet radiation. The chute section with cracks shall be replaced (or repaired) in a timely manner, and the interface of the slide shall be treated in a timely manner in case of unevenness, inverted boss or cracks.

6、金属构件表面漆层在非使用期间应检查是否有脱落、褪色，若有剥皮、脱落现象应补漆。

6. The paint layer on the surface of metal components shall be checked for peeling and fading during non use, and the paint shall be repaired in case of peeling and fading.

7、要定期组织安全检查维护，发现滑梯道面有积水、有砂石、水垢等，应及时用棉布或砂纸清理、打磨。

7. Regularly organize safety inspection and maintenance. If water, sand and scale are found on the surface of the slide, they should be cleaned and polished with cotton cloth or sandpaper.

玻璃钢滑梯的维修：

Repair of FRP slide:

1、滑梯漏水：连接玻璃胶老化，先铲除旧胶，并清理干净，重新打玻璃胶密封，用手抹平，对残余的玻璃胶要进行刮除，待干燥后用水砂纸进行表面打磨处理。

1. Water leakage of slide: when the glass glue is aged, remove the old glue first, clean it up, seal it with glass glue again, level it with hands, scrape off the residual glass glue, and polish the surface with sandpaper after it is dry.

2、滑梯裂纹：用角磨机先把裂纹打磨掉，在修补前把打磨的表面清理干净（用毛刷或棉布），再用同颜色胶衣进行修补，固化后，先用400#水砂纸进行粗打磨，再800#水砂纸进行半精打磨，后用1500#水砂纸进行精打磨，以达到滑梯表面平整、光滑，后用抛光机（配3#抛光液）进行抛光处理。

2. Slide cracks: use an angle grinder to polish off the cracks, clean the polished surface (with a brush or cotton cloth) before repair, and then use gel coat of the same color to repair. After curing, first use 400 # water abrasive paper for rough grinding, then 800 # water abrasive paper for semi fine grinding, and then use 1500 # water abrasive paper for fine grinding, so that the slide surface is flat and smooth, and then use a polishing machine (with 3 # polishing liquid) for polishing.

玻璃钢滑梯的保养和维修指南就整理到这里了，您对此有什么不了解的地方或者有什么需求就来我们网站https://www.hcseaworld.com进行咨询吧！

Here is the maintenance and repair guide for the fiberglass slide. If you have any questions or needs, please come to our website https://www.hcseaworld.com Consult!